Brainboxes PX-246 Especificaciones Pagina 53
- Pagina / 82
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
53
6.2 CONTROL PUSH-BUTTONS
Description Button
Start Inhibit/Reset
This button places the module into its
‘
START INHIBIT/RESET
’
mode. This
will clear any alarm conditions for which the triggering criteria have been
removed. If S2 is on load and the module is placed into Stop mode, the module
will automatically instruct the changeover device to unload S2 (‘Close S2
Output’ becomes inactive (if used)). If S2 is configured for a generator, the start
signal given to the generator controller will also be removed. Should a remote
start signal be present while operating in this mode, a remote start will not
occur.
Manual
This button places the module into its
‘
MANUAL
’
mode to allow manual
control of the ATS functions. This will start S2 if configured as a generator, and
run it off load.
If the S2 is available off-load in the
‘
MANUAL
’
mode and a remote start
on load signal becomes present, the module will automatically instruct the
changeover device to place S2 on load (‘Close S2 Output’ becomes active (if
used)). Upon removal of the remote start signal, S2 remains on load until
either selection of the
‘
START INHIBIT/RESET
’
or
‘
AUTO
’
modes.
For further details, please see the more detailed description of ‘Manual
operation’ elsewhere in this manual.
Auto
This button places the module into its
‘
AUTO
’
mode. This mode allows the
module to control the function of S1 and S2 automatically. The module will
monitor the remote start input and S1 supply status and once a start request is
made, a start request will be given to S2 if configured to a generator and once
available, placed on load.
Upon removal of the starting signal, the module will automatically transfer the
load from S2 and remove the start signal to the generator observing the stop
delay timer and cooling timer as necessary. The module will then await the next
start event.
For further details, please see the more detailed description of ‘Auto operation’
elsewhere in this manual.
Mode
This button allows the user to cycle through different operating
‘
MODE
’
and
press the TICK
‘ ’
to accept the mode change.
The modes available are:
Test On Load: This mode allows the module start and load S2 for test
purposes.
Test Off Load: This mode allows the module start S2 and leave off load for test
purposes.
Prohibit Return: This mode is used to prevent the module from returning load
the S1 until instructed.
For further details, please see the more detailed description of ‘Mode operation’
elsewhere in this manual.
- DEEP SEA ELECTRONICS PLC 1
- TABLE OF CONTENTS 3
- 1 BIBLIOGRAPHY 6
- 2 INTRODUCTION 7
- 3 SPECIFICATIONS 8
- 3.2 TERMINAL SPECIFICATION 9
- 3.5 LOAD CURRENT SENSING 10
- 3.5.2 CT POLARITY 11
- 3.5.3 CT PHASING 11
- 3.5.4 CT CLASS 11
- 3.6 DIGITAL INPUTS 12
- 3.7 OUTPUTS 12
- 3.8 COMMUNICATION PORTS 13
- 3.8.2 RS232 14
- 3.8.3 RS485 16
- 3.10.1 DIMENSIONS 18
- 3.10.2 PANEL CUTOUT 18
- 3.10.3 WEIGHT 18
- 3.10.4 FIXING CLIPS 19
- 3.11 APPLICABLE STANDARDS 21
- 4 INSTALLATION 25
- 4.1.6 S1 VOLTAGE SENSING 28
- (I1,I2,I3) 29
- 4.1.10 RS485 CONNECTOR 31
- 4.1.11 RS232 CONNECTOR 31
- 4.3 ALTERNATIVE TOPOLOGIES 34
- 4.4 EARTH SYSTEMS 39
- 5 DESCRIPTION OF CONTROLS 40
- 5.2 QUICKSTART GUIDE 41
- 5.3.1 STATUS 43
- 5.3.2 S1 44
- 5.3.3 S2 44
- 5.3.4 EXPANSION 44
- 5.3.5 ALARMS 44
- 5.3.6 EVENT LOG 45
- 5.3.7 SERIAL PORT 46
- 5.3.8 SCHEDULER 50
- 5.3.9 ABOUT 50
- 6.1 CONTROL 52
- 6.2 CONTROL PUSH-BUTTONS 53
- 6.3 LOAD SHEDDING CONTROL 55
- 6.4 START INHIBIT/RESET 56
- 6.5 MANUAL MODE 57
- 6.5.3 STOPPING SEQUENCE 58
- 6.6 AUTOMATIC MODE 59
- 6.6.3 S2 AVAILABLE 60
- 6.6.4 STOPPING SEQUENCE 60
- 6.7 MODE SELECTION 61
- 6.7.2 TEST OFF LOAD 62
- 6.7.3 PROHIBIT RETURN 63
- 7 PROTECTIONS 65
- 7.1 INDICATIONS 66
- 7.2 WARNINGS 67
- 7.3 ELECTRICAL TRIPS 68
- 8.1 STOP MODE 69
- 8.2 MANUAL MODE 69
- 8.3 AUTO MODE 69
- 9.1.1 EDITING A PARAMETER 72
- 9.2 ADJUSTABLE PARAMETERS 73
- 10 COMMISSIONING 75
- 11 FAULT FINDING 76
- 11.4 COMMUNICATIONS 77
- 11.5 INSTRUMENTS 77
- 11.6 MISCELLANEOUS 78
- 12.1.1 PACK OF PLUGS 79
- 12.1.2 INDIVIDUAL PLUGS 79
- 13 WARRANTY 81
- 14 DISPOSAL 81
© 2020, manymanuals.es. Todos los derechos reservados | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales