Brainboxes PX-246 Especificaciones Pagina 27
- Pagina / 82
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation – Terminal Description
27
4.1.3 CONFIGURABLE DIGITAL INPUTS J-K, DSENET
Pin No. Description Cable Size Notes
18 Configurable digital input A
0.5mm²
AWG 20
Switch to negative or positive depending on
configuration
19 Configurable digital input B
0.5mm²
AWG 20
Switch to negative or positive depending on
configuration
20 Configurable digital input C
0.5mm²
AWG 20
Switch to negative or positive depending on
configuration
21 DSENet expansion B (+)
0.5mm²
AWG 20
Use only 120Ω RS485 approved cable
22 DSENet expansion A (-)
0.5mm²
AWG 20
Use only 120Ω RS485 approved cable
23 DSENet expansion SCR
0.5mm²
AWG 20
Use only 120Ω RS485 approved cable
N
NN
NOTE:
OTE:OTE:
OTE:
Terminal 24 is not used, do not connect.
Terminal 24 is not used, do not connect.Terminal 24 is not used, do not connect.
Terminal 24 is not used, do not connect.
4.1.4 CONFIGURABLE VOLT-FREE OUTPUTS E & F
Pin No. Description Cable Size Notes
25 Output relay E
1.0mm
AWG 18
Normally closed volt-free relay user configured (8A
resistive
at 250V AC rated)
26 Output relay E
1.0mm
AWG 18
Normally closed volt-free relay user configured (8A
resistive
at 250V AC rated)
28 Output relay F
1.0mm
AWG 18
Normally open volt-free relay user configured (8A
resistive at
250V AC rated)
29 Output relay F
1.0mm
AWG 18
Normally open volt-free relay user configured (8A
resistive at
250V AC rated)
NOTE: Terminal
NOTE: TerminalNOTE: Terminal
NOTE: Terminal
27 is not used, do not connect.
27 is not used, do not connect.27 is not used, do not connect.
27 is not used, do not connect.
4.1.5 LOAD SWITCHING AND S2 VOLTAGE SENSING
Pin No. Description Cable Size Notes
30 Output relay A
1.0mm
AWG 18
Normally configured to control S1 contactor coil
(Recommend 10A fuse)
31 Output relay A
1.0mm
AWG 18
Normally configured to control S1contactor coil
32 Output relay B
1.0mm
AWG 18
Normally configured to control S2 contactor coil
(Recommend 10A fuse)
33 Output relay B
1.0mm
AWG 18
Normally configured to control S2 contactor coil
S2
34 S2 L1 (U) voltage monitoring
1.0mm²
AWG 18
Connect to S2 L1 (U) output (AC)
(Recommend 2A fuse)
35
S2 L2 (V) voltage monitoring
input
1.0mm²
AWG 18
Connect to S2 L2 (V) output (AC)
(Recommend 2A fuse)
36
S2 L3 (W) voltage
monitoring input
1.0mm²
AWG 18
Connect to S2 L3 (W) output (AC)
(Recommend 2A fuse)
37 S2 Neutral (N) input
1.0mm²
AWG 18
Connect to S2 Neutral terminal (AC)
NOTE:
NOTE:NOTE:
NOTE:
The above table describes connections to a three phase, four wire alternator.
The above table describes connections to a three phase, four wire alternator. The above table describes connections to a three phase, four wire alternator.
The above table describes connections to a three phase, four wire alternator.
For alternative wiring topologies, please see the ALTERNATIVE
For alternative wiring topologies, please see the ALTERNATIVEFor alternative wiring topologies, please see the ALTERNATIVE
For alternative wiring topologies, please see the ALTERNATIVE
AC TOPOLOGIES section of
AC TOPOLOGIES section of AC TOPOLOGIES section of
AC TOPOLOGIES section of
this manual.
this manual.this manual.
this manual.
- DEEP SEA ELECTRONICS PLC 1
- TABLE OF CONTENTS 3
- 1 BIBLIOGRAPHY 6
- 2 INTRODUCTION 7
- 3 SPECIFICATIONS 8
- 3.2 TERMINAL SPECIFICATION 9
- 3.5 LOAD CURRENT SENSING 10
- 3.5.2 CT POLARITY 11
- 3.5.3 CT PHASING 11
- 3.5.4 CT CLASS 11
- 3.6 DIGITAL INPUTS 12
- 3.7 OUTPUTS 12
- 3.8 COMMUNICATION PORTS 13
- 3.8.2 RS232 14
- 3.8.3 RS485 16
- 3.10.1 DIMENSIONS 18
- 3.10.2 PANEL CUTOUT 18
- 3.10.3 WEIGHT 18
- 3.10.4 FIXING CLIPS 19
- 3.11 APPLICABLE STANDARDS 21
- 4 INSTALLATION 25
- 4.1.6 S1 VOLTAGE SENSING 28
- (I1,I2,I3) 29
- 4.1.10 RS485 CONNECTOR 31
- 4.1.11 RS232 CONNECTOR 31
- 4.3 ALTERNATIVE TOPOLOGIES 34
- 4.4 EARTH SYSTEMS 39
- 5 DESCRIPTION OF CONTROLS 40
- 5.2 QUICKSTART GUIDE 41
- 5.3.1 STATUS 43
- 5.3.2 S1 44
- 5.3.3 S2 44
- 5.3.4 EXPANSION 44
- 5.3.5 ALARMS 44
- 5.3.6 EVENT LOG 45
- 5.3.7 SERIAL PORT 46
- 5.3.8 SCHEDULER 50
- 5.3.9 ABOUT 50
- 6.1 CONTROL 52
- 6.2 CONTROL PUSH-BUTTONS 53
- 6.3 LOAD SHEDDING CONTROL 55
- 6.4 START INHIBIT/RESET 56
- 6.5 MANUAL MODE 57
- 6.5.3 STOPPING SEQUENCE 58
- 6.6 AUTOMATIC MODE 59
- 6.6.3 S2 AVAILABLE 60
- 6.6.4 STOPPING SEQUENCE 60
- 6.7 MODE SELECTION 61
- 6.7.2 TEST OFF LOAD 62
- 6.7.3 PROHIBIT RETURN 63
- 7 PROTECTIONS 65
- 7.1 INDICATIONS 66
- 7.2 WARNINGS 67
- 7.3 ELECTRICAL TRIPS 68
- 8.1 STOP MODE 69
- 8.2 MANUAL MODE 69
- 8.3 AUTO MODE 69
- 9.1.1 EDITING A PARAMETER 72
- 9.2 ADJUSTABLE PARAMETERS 73
- 10 COMMISSIONING 75
- 11 FAULT FINDING 76
- 11.4 COMMUNICATIONS 77
- 11.5 INSTRUMENTS 77
- 11.6 MISCELLANEOUS 78
- 12.1.1 PACK OF PLUGS 79
- 12.1.2 INDIVIDUAL PLUGS 79
- 13 WARRANTY 81
- 14 DISPOSAL 81
© 2020, manymanuals.es. Todos los derechos reservados | 0.199 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales